Ground Set Cone Tapered Aluminum Flagpoles - GENERAL INFORMATION

Aluminum Flagpole Pricing

Fiberglass Flagpole Pricing

Ground Set Cone Tapered Aluminum Flagpoles

Our cone tapered ground set aluminum flagpoles are precision fabricated from new, 6063-T6 tubing utilizing the industry’s most sophisticated, state-of-the-art manufacturing processes.  The conical portion tapers approximately 1” in every 5 ½ feet.  Poles with overall lengths of less than 38’6” are shipped in one piece.  Longer lengths are shipped in sections and will be factory fitted with a self-aligning sleeve which requires no field welding.  Upon proper assembly a hair-line joint will occur.

All poles are double spiral wrapped with protective paper and shipped in a hard fiber tube. 
‘Warning” – the flagpole shaft will stain if allowed to remain in contact with wet or damp wrappings.  If there is any sign that the shaft or its shipping tube has come in contact with water during shipment, remove it from the tube and unwrap immediately.  If the shaft is to be stored outdoors, it must be stored unwrapped, out of the tube, and off the ground.  If the shaft is to be stored indoors, it may be left in the wrappings and the tube, provided that it shows no sign of having been exposed to moisture, and that it will not be exposed to moisture during storage.

 All foundation dimensions are intended for general guidelines only in good, firm, dry soil.  It is recommended to consult an engineer for specific foundation dimensions suited to your exact location.  “Warning” – Extreme care must be exercised when installing flagpoles near overhead power lines or when digging in the vicinity of buried cable or piping.  Contact your local authorities before any digging.

 Standard Finishes 

All flagpole shafts are highly polished with fine grain aluminum oxide cloth resulting in a high quality, deep satin luster finish.  This finish represents the ultimate in architectural finishes for aluminum flagpoles.  The elegant, soft sheen remains maintenance free.  In addition to satin, the following anodized finishes are available as standard colors: clear, light bronze #311, medium bronze #312, dark bronze #313 & black #335.  Note:  of the three bronze finishes, dark bronze #313 is supplied unless otherwise specified.   

Click on Color for Larger View

Satin Flagpole Finish Clear Flagpole Finish Bronze 311 Flagpole Finish Bronze 312 Flagpole Finish Bronze 313 Flagpole Finish Black Flagpole Finish
Satin Clear Bronze #311 Bronze #312 Bronze #313 Black

Custom Finishes

In addition to the above standard finishes, we offer alternate finishes which may suit particular job conditions better.  Among these are:  Kalcolor (light amber, amber, gold & statuary bronze), Kynar 500 (your choice of color), Duracron-baked acrylic (your choice of color) or gold anodized (shafts up to 20’). 


WIND CHART

The map below shows the maximum steady wind expected at an elevation of thirty feet above ground level within a fifty-year period of recurrence.  Areas with the same maximum constant or steady wind speed are indicated.  Because wind speeds are usually not constant, and gusts are involved, flagpoles (both flagged and unflagged) are listed with a constant wind speed and with a 1.3 gust factor.
"WARNING" - recommended flag sizes do not represent a warranty that the flag size shown may be safely flown in all wind speeds.  Personal injury, flagpole damage or property damage can occur when flying over-sized flags and banners or flying flags in higher winds than recommended.  Flagpoles and their associated wind speeds listed assume that ten percent of the overall length of the flagpole is buried per our recommendations at or near ground level.  Special engineering may be required for other applications such as wall or roof mounted flagpoles. 

Procedures used to determine wind loads on flagpoles are those set forth by the American, AASTO, for the design of structural supports for highway signs, luminaries and traffic signals.

Design of safe flagpoles requires knowledge of the loads to which they will be subjected.  Principal load acting on flagpoles is wind load and that load must be carefully determined.  Maximum wind speeds to which flagpoles are exposed depend on geographical location, whether or not it is in the center of a large city, a small town's outskirts, seashore, at ground level or on the roof of a high building.  Wind speeds generally are higher along coastal areas than inland.  They are also higher in open country than in the center of cities.  Wind speed also    becomes greater as height above ground increases.  Wind exerts a force on the pole as well as the flag, thus both loads must be added to determine total load.  Flags of different sizes are designed to be flown from different poles.  Obviously, it is important that flagpoles be selected which are capable of supporting the largest flag intended to be flown in the highest wind speed to which it will be subjected.  Loads on flagpoles are resisted by the mounting foundation, roof or wall to which it is secured.

 

To order call 800-225-FLAG (3524)

FAX:  573-372-3411

or email excelsales@charter.net

  Order Form

Excel Sails Flags and Flagpoles
32968 Stonecroft Drive
Gravois Mills, MO 65037

USA Flags on Sale

Return to Home

Thank you for visiting our Ground Set Cone Tapered Aluminum Flagpoles - Information